Sculpt Blaster
- 240 × 65 mm — narrow, follows the body line
- S curve: fits the waist and the calf, not just flat planes
- Open frame — light in the hand through long sessions
- Solid urapán (Fraxinus uhdei) — a dense hardwood that holds an edge
An S curve with a hollow centre, 240 mm long, sold as a pair. The profile follows a waist, an arm or a calf instead of sitting across it — where a straight board only touches at two points and all the pressure goes there.
Smooth edges, no teeth. This is a closing tool: it directs fluid after the deeper phases have done their work.
Worked toward the nodes
Long, slow strokes with the whole curve in contact, always toward the nearest lymph nodes — groin for the legs, armpit for the arms and back. Manual lymphatic drainage is a recognised technique in aesthetics and physiotherapy, and the movement here follows the same direction and the same unhurried pace. What a wooden tool adds is reach and consistency, not a different mechanism.
(Source: The Utility of Lymphatic Massage in Cosmetic Procedures — PubMed Central; Lymphatic Drainage Massage: What It Is & Benefits — Cleveland Clinic.)
Designed by experts
Working the fascia
Sustained pressure with a smooth tool is the basis of myofascial work, which is used to improve tissue mobility, ease tension and support circulation. On the specific question of whether any handheld tool changes the appearance of dimpled skin, the honest answer is that the evidence is thin — we are not going to tell you otherwise.
(Source: Does Fascia Blasting Work and Is It Safe? — Healthline. A second reference previously cited here has been removed because we could not verify it.)
Where it works
The S curve is cut for areas that are not flat:
✦ The waist and the flank, following the line inward.
✦ Arms and calves, where a straight board bridges across the limb.
✦ The thigh, 360°, including the inner face.
✦ The back, worked either side of the spine and never on it.
Not the right tool for
Flat planes — the curve has nothing to follow on a back and the open centre gives you less contact, not more. Also not for depth: the edges are smooth by design. Never over bone, varicose veins, open wounds or fresh scar tissue. Post-operative work only from the point the treating surgeon has cleared in writing.
Maximize Your Results
A tool that does not glide drags, and dragging is what marks skin. Use it with enough massage oil for the whole curve to slip.
See how tools like the Sculpt Blaster fit into a full session in our wood therapy tool guide.
How does it work?
Taking care of your pieces
Would you like to customize your products?
Choose options
- Made by us Cut and finished in our own workshop in Colombia
- Solid urapán Fraxinus uhdei — dense enough to hold an edge under pressure
- Ships worldwide Tracked delivery to professionals in eight countries
- Trade pricing From 10 pieces, with your clinic's name engraved See wholesale tiers
An S curve with a hollow centre. It wraps a limb instead of bridging it.
Indicated for
Where this tool earns its place
Not the right tool for
Flat planes — the S curve has nothing to follow on a back and the open centre gives you less contact, not more. Also not for depth: the edges are smooth by design. Not over bone, varicose veins, open wounds or fresh scar tissue.
- Curved areasThe S profile follows a waist or a calf rather than sitting across it.
- Smooth edgesNo teeth — contouring and drainage, not mobilisation.
- Open frameThe hollow centre lets the curve seat properly on a limb.
- Arm and calfWhere a straight board only touches at two points.
- 240 mm, one-handedLong enough to be efficient, light enough to control.
- Post-operative stagesOnly from the point the treating surgeon has cleared in writing.
Technical sheet
Specifications
These pieces are handmade by our artisans, so measurements may vary by a few millimetres.
| Overall length | 240 mm 9.4 in |
|---|---|
| Overall width | 65 mm 2.6 in |
| Profile | S curve, open frame hollow centre |
| Edges | Smooth, rounded no teeth |
| Wood | Urapán (Fraxinus uhdei) solid, dense hardwood |
| Finish | Natural, unvarnished sanded to a closed grain |
| Technique | Woodtherapy contouring along curves |
| Body areas | Waist, thigh, arm, calf |
Technique
How to work with it
- 01
Match the curve to the body
Find the orientation where the S sits against the limb along its whole length. That is the tool working; anything else is a stick.
- 02
Use it in the closing phase
Smooth edges are for directing fluid, after the deeper work is done.
- 03
Long slow passes toward the nodes
Ankle to groin, wrist to armpit. Keep contact through the whole stroke.
- 04
Finish by hand
Close with manual drainage at the nodes.
Made by hand
We are the workshop, not the middleman
Every KOWÜA tool is turned on our own lathes. We select the timber, cut it, turn it, sand it through progressive grits and finish it by hand. Nothing is bought in and rebranded.
We work with urapán (Fraxinus uhdei) because it is a dense hardwood with a fine closed grain — the surface stays smooth against skin instead of raising fibres after a few washes — and because it takes pressure without splitting.
Buying direct means the price of the factory, custom laser engraving with your clinic’s name, and someone who can actually change the tool if you need a different profile.
Care
Cleaning and sanitising
Never
Do not autoclave, do not soak, do not put it in a dishwasher and do not leave it submerged in disinfectant. Wood is porous — immersion swells the fibre, raises the grain and will crack the piece.
- After each clientWipe off oil residue with a dry or barely damp cloth, while the tool is still warm.
- Disinfect70% alcohol on the surface, then let it air-dry completely.
- StoreDry and flat, away from direct heat and sun.
If the surface ever feels rough, a light pass with fine sandpaper along the grain restores it. That is the advantage of an unvarnished finish: it can be renewed, and there is no coating to chip into a client’s skin.
Before you order
Questions we get
How do I know it is the right size?
It is 240 mm end to end. The full specification table is above.
Can I use it on post-surgical clients?
Only with written clearance from the treating surgeon, who alone decides when a patient may progress from gentle manual lymphatic drainage to firmer tooled work. Clearance timelines vary widely between surgeons and between patients, and we publish none. Never on fresh incisions.
Does it need oil?
Yes. A dry tool on dry skin drags and bruises. Any professional massage oil works; ours are formulated to keep slip without soaking into the wood.
How long does the wood last?
With correct care — no immersion, no autoclave — solid urapán lasts years of daily clinic use. Urapán is a dense hardwood, which is why it holds a working edge instead of denting.
Will it mark the skin?
Redness and warmth during a session are expected. Bruising is not — it means too much pressure, or a tool too deep for that tissue. Treatment should never be painful.
Can I get my clinic’s name on it?
Yes. We laser-engrave logos and names from 10 pieces. See wholesale tiers and engraving.
Do you ship outside Colombia?
Yes, worldwide with tracking. For orders of 10 pieces or more we quote freight directly.
Which tool comes next?
Depends what you already have. Our wood therapy tool guide ranks every surface we make by depth and shows where each one belongs in a session.
Buying for a clinic or academy?
Wholesale starts at ten pieces
Mix and match any references. Discounts from 15%, custom laser engraving with your clinic’s name, and freight quoted directly so you are not paying retail rates.
See wholesale pricing